![younger season 1 episode 10 subtitles younger season 1 episode 10 subtitles](http://blog.obdii365.com/wp-content/uploads/2020/03/bmw-f-i-g-program-1.jpg)
CAS)ģ.Do not cut the connection between workshop network, vehicle interface and vehicleĤ.Close the boot lid again after any action in the luggage compartment (e.g. loading/removing navigation DVD) to prevent the luggage compartment lighting from overheatingĥ.During programming, perform no other activities on/in the vehicle than those instructed by ISTA/P.ġ.Execute procedure for finishing off the measures plan and confirm by clicking “OK” Data media in a drive or still connected could cause programming to abortġ9.Before starting vehicle programming, make sure the boot lid is closed (to prevent the luggage compartment lighting from overheating).ġ.Observe and follow requests and instructions in ISTA/PĢ.Leave ignition switched on and follow instructions in ISTA/P (e.g. Make sure that the driver’s door contact is not operated during the programming procedure.ġ5.Perform a vehicle test with the ISTA workshop system to make sure that all installed control modules respond and any fault memory entries are read outġ6.Before programming, rectify any faults that may be present and delete any fault codes storedġ7.Determine CBS data, note down and end ISTA workshop systemġ8.Preparations: Remove inserted data media (DVD) and disconnect connected data (iPod®, etc.). Terminal 15 is permanently switched on by pressing the START-STOP button. − On vehicles with automatic terminal 15 shutdown (as from 03/2007) the signal from the door contact switches off terminal 15 by opening and closing the driver’s door. − If the vehicle model does not have an ignition lock, the identification transmitter must be located in the vehicle interior. The coding procedure may be terminated if the identification transmitter is not inserted in the ignition lock. − On vehicles with Comfort Access, the identification transmitter must be inserted in the ignition lock.
YOUNGER SEASON 1 EPISODE 10 SUBTITLES WINDOWS
Cables routed through open windows could be damaged when the windows are started automatically. Make sure that the vehicle system voltage does not drop below 13.0 volts while programming is in progressġ2.Set up connection between workshop network, vehicle interface and vehicleġ3.Check cable routing. Low system voltage may cause programming to cancel. Please refer to the operating instructions for the battery chargerġ1.Do not connect or disconnect the battery charger during programming. The battery charger connected during programming must be run in “external power supply mode with battery connected”.
![younger season 1 episode 10 subtitles younger season 1 episode 10 subtitles](http://www.eobdtool.com/blog/wp-content/uploads/2017/07/rheingold-bmw-ista-software.jpg)
YOUNGER SEASON 1 EPISODE 10 SUBTITLES TV
Make sure that the wipers can move freelyĩ.Make a note of all stored radio and TV frequencies as well as the navigation destinationsġ0.Connect up a BMW Group-approved battery charger in the engine compartment. The wipers may be actuated during programming and initialization. ISTA-D 3.53.30 ISTA-P 3.57.4.5.Activate electromechanical parking brake or apply parking brakeĦ.Make sure that the temperature of the transmission fluid is between -40 ☌ (-40 ☏) and 85 ☌ (185 ☏)ħ.Switch off all electric loads, lights and turn signal lampsĨ.Switch off wiper/washer system. ISTA P ISPI Next Info: service and language settings The newest version will work with newer BMW vehicle models.įollowing post will one-by-one show you following information: BMW ISTA-D 3.53.30 ISTA-P 3.57.4.003 with engineer programming run on Windows 8īMW ISTA-D 3.53.30 ISTA-P 3.57.4.003 with engineer programming is verified working fine, it can run on Windows 8.